HS 300 Large Adjustable Height Work Table - Beck products are characterised by technology, quality
and know-how. In particular, our unique selling point, the double horizontal scissor construction,
ensures maximum stability with two fixed bearings and two floating bearings.
[NB this is the base unit only - tops can be added as extra to customise your solution]
Max load 300 kg
Useful stroke 610 mm
Height of the lifting table 400 mm
Weight approx. 150 kg
4 swivel castors (wheel ¢ 125 mm), 2 of which have brakes
CMT part no:DET-001
Attach this trimmer to your workpiece, press both ends against the board for a cutting range between 13mm (1/2") and 25mm (1"), move the trimmer in the correct direction indicated by the arrow. This will cut on both sides easily. The first cutter will cut straight, the second one can be adjusted for a chamfer cut.
Both cutters are made from high-quality hardened steel and can be easily replaced when worn out [ Part no CMDET001K]
suitable for up to 0.6mm edging
CMT part no:DET-002
Edge banding end trimmer
An indispensable tool for easy and safe end trimming after edge banding. Position the tool on the banding, press down on the handle to operate the blade in a shearing action. The cutting knives are interchangeable, so when the cutting knife becomes dull, you can simply replace it with the anvil knife for a double lifetime. For cutting banding up to 0,5mm thick with a maximum cutting width of 54mm.
This tool can also be paired up with our double edge trimmer DET-001.
We recommend using our edge banding end trimmer DET-002 before
using our double-edge trimmer DET-001.
CMT part no:DET-004
CMT Edgebanding Iron 230v
Apply pre-glued edge banding easily and accurately. The iron non-stick surface allows smooth and easy application. The thermostatically controlled short preheat time gets you working quicker. Includes heat resistant metal base to place iron
when not using it.
- Includes thermostatic heat control.
- Non-stick coating.
- Specially shaped shoe with rounded edges.
- Metal stand.
- 154cm (5-1/2') power cord, 230V.
Made with both professionals and hobbyists in mind, the VH03 Vacuum Clamp Set is suited for edgebanding or edge tape application on large work pieces, including doors, panels, and countertops.
Quick Setup
Simply adhere the vacuum or C-clamp to stabilizing surface and workpiece, and flip the fasteners.
Secure Your Workpieces
Each vacuum cup can hold up about 34kg (75lbs) of pressure.
Scuff-Free Fastening
Since the vacuum cups are made of rubber, there will be no need to worry about potential damage to the workpiece or stabilizing surface.
Easy Transportation
Each VH03 Vacuum Clamp Set comes with two vacuum clamps and an interlockable Cruiser Case.
The iTECH Panel Saw Trolley is the ultimate workshop companion, designed to simplify manual handling tasks. Ideal for single-person loading of 8x4 or 10x5 ft sheets onto horizontal saws or CNC Routers.
This trolley features rubber idle rollers for effortless offloading. With adjustable height settings and a balanced design, transitioning sheets from vertical to horizontal is easy and efficient.
The EASY Lift panel trolley ensures safe and affordable handling, making it a must-have for any woodworking or manufacturing workshop.
Support rail distance 1150mm internal
1235mm external
Packed dimensions 1500 x 480 x 110mm
Spray onto the upper and lower edge area of the workpiece
-Statically discharges the edge area
-Cooling of the glue joint and hardening of the glue
-Tracers and workpieces remain free of chippings
Tooling remains free of glue residue
To cool the glue joint and statically discharge the edging material. The perfect addition to the release agent spraying system fitted at the machine infeed and the cleaning agent spraying system fitted at the end of the machine is the antistatic coolant system. It can be fitted downstream of the last contact pressure roller, upstream of the cross cut saws or upstream of the radius milling stations.
The Antistatic Coolant LP289/99? is sprayed directly on the glue joint and on the edging material by means of our spraying systems. As a result the glue joint surface is hardened. The glue build-up on the tools is notably reduced and consequently the glue is no longer transferred onto the edging material (indispensable for PUR). Furthermore, the edging material is statically discharged. Tracer rollers and workpieces remain free from milling chips. Milling of (flush trimming) the PVC/PP/etc. edges causes static charging of the edging material and the adjoining top and bottom face of the workpieces. Milled off chips adhere to the edging material and on the top and bottom surface of the panel negatively impairing the function of the tracer rollers and making a precise finishing by scraper blades or milling impossible. This system remedies the above problems instantly!
Spray onto the upper and lower edge area of the workpiece.
-Statically discharges the edge area
-Cooling of the glue joint and hardening of the glue
-Tracers and workpieces remain free of chippings
Tooling remains free of glue residue
To cool the glue joint and statically discharge the edging material. The perfect addition to the release agent spraying system fitted at the machine infeed and the cleaning agent spraying system fitted at the end of the machine is the antistatic coolant system. It can be fitted downstream of the last contact pressure roller, upstream of the cross cut saws or upstream of the radius milling stations.
The Antistatic Coolant LP289/99 is sprayed directly on the glue joint and on the edging material by means of our spraying systems. As a result the glue joint surface is hardened. The glue build-up on the tools is notably reduced and consequently the glue is no longer transferred onto the edging material (indispensable for PUR). Furthermore, the edging material is statically discharged. Tracer rollers and workpieces remain free from milling chips. Milling of (flush trimming) the PVC/PP/etc. edges causes static charging of the edging material and the adjoining top and bottom face of the workpieces. Milled off chips adhere to the edging material and on the top and bottom surface of the panel negatively impairing the function of the tracer rollers and making a precise finishing by scraper blades or milling impossible. This system remedies the above problems instantly!
Ensure the consistent high quality of your work-pieces by including the cleaning of the chain plates in your maintenance cycle.
Contaminated chain plates lessen the grip on the workpiece and as a result the applied pressure of the top pressure belt has to be increased. In addition, contaminated chain plates can result in markings on the workpieces.
Our specially developed Cleaning Agent LP407/13 for chain plates, top pressure belts and rubberised roller conveyors will greatly assist in cleaning without attacking any of the materials.
-Specially developed for the cleaning of chain plates, top pressure belts and rubberised roller conveyors
-High cleaning power
-Materials not affected
-Consistent grip of the workpiece
-No Change in the shore hardness
Unsuitable cleaners can cause damage to the sur-face of the plates. In addition, a change in the shore hardness can occur.
Even a liberal use of LP407/13 has no negative ef-fect on the chain plates, top pressure belts or roller conveyors.
Application:
With the machine stationary, use a well wetted lint free cloth to clean plate by plate.
Available containers: 10 Litre | 30 Litre
Ensure the consistent high quality of your work-pieces by including the cleaning of the chain plates in your maintenance cycle.
Contaminated chain plates lessen the grip on the workpiece and as a result the applied pressure of the top pressure belt has to be increased. In addition, contaminated chain plates can result in markings on the workpieces.
Our specially developed Cleaning Agent LP407/13 for chain plates, top pressure belts and rubberised roller conveyors will greatly assist in cleaning without attacking any of the materials.
-Specially developed for the cleaning of chain plates, top pressure belts and rubberised roller conveyors
-High cleaning power
-Materials not affected
-Consistent grip of the workpiece
-No Change in the shore hardness
Unsuitable cleaners can cause damage to the sur-face of the plates. In addition, a change in the shore hardness can occur.Even a liberal use of LP407/13 has no negative ef-fect on the chain plates, top pressure belts or roller conveyors.
Application:
With the machine stationary, use a well wetted lint free cloth to clean plate by plate.
Available containers: 10 Litre | 30 Litre
Spray onto the upper and lower edge area of the workpiece:
- Removal of release agent and loose glue residue
- Cooling of the edgeband and glue joint
- Matt radius of the machined edgeband re-matches the surface finish
Area of application: Before buffing wheels / surface scraper.
This system is used to spray the Cleaning Agent LP163/93 on the top and bottom surface of the board edge, as well as the edgeband. The release agent applied at the machine infeed side and the loose glue residue are removed by the application of the cleaning agent and subsequent buffing.
Furthermore, the glue joint and the edge banding are cooled. Heat generation during buffing is considerably reduced by the application of the liquid. Smearing of glue emerging from the joint is avoided. The edge banding radius is wet buffed with the special Cleaning Agent LP163/93.
Moreover, the radius is polished to match the surface sheen. Glue residue no longer adheres to the buffing wheels. Result: An absolutely clean board edge!
This result can only be obtained when the buffing wheels are used without oscillation and applying only slight pressure. The buffing disc must be used with an inclination in relation to the workpiece of 3 degrees, 10 degrees inclined to the support and with a lateral overhang of 5mm to the workpiece edge. Rotational direction should be in synchronous run to reduce heat generation.
At the currently installed flat scrapers with skids the fine nozzles are arranged directly in front of the flat scraper. This prevents the adhesion of glue residue on the scrapers and skids.
Consumption per fine nozzle: Under 1 liter for 5000 running meters. The electronically controlled cleaning agent spraying system only requires a compressed air connection of 3 bar and a 230/24 V socket.
The special plastic cleaners developed by RIEPE? are the first choice for the manual cleaning of plastic surfaces. Due to the exclusive use of only high quality raw materials, the RIEPE? special plastic cleaners affirm their position as premium products in the market.
-Effortlessly removes glue residues
-Strong cleaning power
-Quick drying
-Residue free evaporation
-Low odour
-Hexane free
-Benzene free
The special plastic cleaners developed by RIEPE? are the first choice for the manual cleaning of plastic surfaces. Due to the exclusive use of only high quality raw materials, the RIEPE? special plastic cleaners affirm their position as premium products in the market.
-Effortlessly removes glue residues
-Strong cleaning power
-Quick drying
-Residue free evaporation
-Low odour
-Hexane free
-Benzene free
Spray onto the upper and lower edge area of the workpiece:
Removal of release agent and loose glue residue
Cooling of the edgeband and glue joint
Matt radius of the machined edgeband re-matches the surface finish
Area of application: Before buffing wheels / surface scraper
This system is used to spray the Riepe Cleaning Agent LP163/93. On the top and bottom surface of the board edge, as well as the edgeband. The release agent applied at the machine infeed side and the loose glue residue are removed by the application of the cleaning agent and subsequent buffing.
Furthermore, the glue joint and the edge banding are cooled. Heat generation during buffing is considerably reduced by the application of the liquid. Smearing of glue emerging from the joint is avoided. The edge banding radius is wet buffed with the special Cleaning Agent LP163/93. As a consequence, heating of the thermoplastic material is notably reduced, and a smearing of the plastic is prevented.
Moreover, the radius is polished to match the surface sheen. Glue residue no longer adheres to the buffing wheels.
Result: An absolutely clean board edge!
This result can only be obtained when the buffing wheels are used without oscillation and applying only slight pressure. The buffing disc must be used with an inclination in relation to the workpiece of 3 degrees, 10 degrees inclined to the support and with a lateral overhang of 5mm to the workpiece edge. Rotational direction should be in synchronous run to reduce heat generation.
At the currently installed flat scrapers with skids the fine nozzles are arranged directly in front of the flat scraper. This prevents the adhesion of glue residue on the scrapers and skids.
Consumption per fine nozzle: Under 1 liter for 5000 running meters. The electronically controlled cleaning agent spraying system only requires a compressed air connection of 3 bar and a 230/24 V socket.
Intermittent application to the pressure roller
Use within high heat zones possible
Contamination of the roller is prevented
The fine nozzle of this electronically controlled unit applies the Release Agent NFLY? to the contact pressure roller. This is achieved by adjustable timing interval. The spray duration is about 3 seconds. In this way glue is prevented from adhering to the contact pressure rollers. In addition the special release agent is taken from the edge and transferred to the downstream contact pressure rollers or anti-friction shoes. The contact pressure rollers and the anti-friction shoes remain free of glue residue. The anti-friction shoes are simultaneously cooled. Result: A notably enhanced quality. Contact pressure rollers and anti-friction shoes need no longer be cleaned.
Intermittent application to the pressure roller
Use within high heat zones possible
Contamination of the roller is prevented
The fine nozzle of this electronically controlled unit applies the Release Agent NFLY? to the contact pressure roller. This is achieved by adjustable timing interval. The spray duration is about 3 seconds. In this way glue is prevented from adhering to the contact pressure rollers. In addition the special release agent is taken from the edge and transferred to the downstream contact pressure rollers or anti-friction shoes. The contact pressure rollers and the anti-friction shoes remain free of glue residue. The anti-friction shoes are simultaneously cooled. Result: A notably enhanced quality. Contact pressure rollers and anti-friction shoes need no longer be cleaned.
Spray onto the upper and lower edge area of the workpiece. Prevents the adhesion of emerging glue onto the workpiece.
Area of application: Prior to the pre-milling
Upstream of the formatting unit, an ultra-thin coat of the Release Agent is applied to the top and bottom surface of the workpieces (edge area) by means of electronically controlled release agent spraying system. This prevents squeezed out glue from adhering to the workpiece.
An ultra-thin application of the release agent in the edge area (consumption per nozzle under 1 liter per 5000 running meters) guarantees a perfect result. The electronically controlled release agent spraying system only requires a 3 bar compressed air connection and a 230/24V outlet. The special release agents are adapted to all commercially available glues.
Spray onto the upper and lower edge area of the workpiece. Prevents the adhesion of emerging glue onto the workpiece.
Area of application:Prior to the pre-milling
Upstream of the formatting unit, an ultra-thin coat of the Release Agent is applied to the top and bottom surface of the workpieces (edge area) by means of electronically controlled release agent spraying system. This prevents squeezed out glue from adhering to the workpiece.
An ultra-thin application of the release agent in the edge area (consumption per nozzle under 1 liter per 5000 running meters) guarantees a perfect result. The electronically controlled release agent spraying system only requires a 3 bar compressed air connection and a 230/24V outlet. The special release agents are adapted to all commercially available glues.
High heat resistant: for use on machines with high heat zones (e.g. Post-/Softforming)
Workpieces can pass through high heat zones without any effect on the performance of the release agent
Prevents the adhesion of emerging glue residue onto the workpiece
Areas of application:
(a) Pressure roller
(b) Edgeband/ protective foil
(c) Slide shoe
(d) DUO scraper
(e) Tooling
(a) Intermittent application to the pressure roller
Glue residues cannot adhere to the roller
(b) Spray directly onto the surface of the edgeband
Avoidance of marking and damage
Protective film is protected and not removed from the edge
(c) Edge/protective foil automatically transfers the release agent to the slide shoes
Glue residues do not adhere Prevents marking and friction
(d) Direct application onto the DUO scraper
No clogging of the DUO scraper
(e) Application to the tooling
Prevents fouling of the trimmers
The fine nozzle of this electronically controlled unit applies the Release Agent NFLY? to the contact pressure roller. This is achieved by adjustable timing interval. The spray duration is about 3 seconds. In this way glue is prevented from adhering to the contact pressure rollers. In addition the special release agent is taken from the edge and transferred to the downstream contact pressure rollers or anti-friction shoes. The contact pressure rollers and the anti-friction shoes remain free of glue residue. The anti-friction shoes are simultaneously cooled. Result: A notably enhanced quality. Contact pressure rollers and anti-friction shoes need no longer be cleaned.
Post-/Softforming:
For Post-/Softforminhg work, the Release Agent NFLY? is sprayed directly on the top coat in front of the anti-friction shoes. The special release agent is transferred to the anti-friction shoes to form a glide film.
This prevents squeezed out glue residue from adhering to them and the workpiece.
Areas of application:
(a) Pressure roller
(b) Edgeband/ protective foil
(c) Slide shoe
(d) DUO scraper
(e) Tooling
(a) Intermittent application to the pressure roller
Glue residues cannot adhere to the roller
(b) Spray directly onto the surface of the edgeband
Avoidance of marking and damage
Protective film is protected and not removed from the edge
(c) Edge/protective foil automatically transfers the release agent to the slide shoes
Glue residues do not adhere Prevents marking and friction
(d) Direct application onto the DUO scraper
No clogging of the DUO scraper
(e) Application to the tooling
Prevents fouling of the trimmers
The fine nozzle of this electronically controlled unit applies the Release Agent NFLY? to the contact pressure roller. This is achieved by adjustable timing interval. The spray duration is about 3 seconds. In this way glue is prevented from adhering to the contact pressure rollers. In addition the special release agent is taken from the edge and transferred to the downstream contact pressure rollers or anti-friction shoes. The contact pressure rollers and the anti-friction shoes remain free of glue residue. The anti-friction shoes are simultaneously cooled. Result: A notably enhanced quality. Contact pressure rollers and anti-friction shoes need no longer be cleaned.
Post-/Softforming:
For Post-/Softforminhg work, the Release Agent NFLY? is sprayed directly on the top coat in front of the anti-friction shoes. The special release agent is transferred to the anti-friction shoes to form a glide film.
This prevents squeezed out glue residue from adhering to them and the workpiece.
BAM 308 is a new concept in edgebanding hot melt adhesives based on the idea that for quality woodworking operations, adhesives should be clean, easy to handle, odourless and not fume, being unfilled this enables the coating weight to be substantially reduced leading to a significant increase in mileage with no sacrifice in performance. A very high tack adhesive providing excellent adhesion to difficult substrates such as primed PVC and high pressure laminates.
Applications
Woodworking
An unfilled medium viscosity adhesive for soft forming and edgebanding where difficult substrates are used, e.g. PVC, HPL, Solid Wood etc.
No filler so very little burning is encountered
BAM 308 is a new concept in edgebanding hot melt adhesives based on the idea that for quality woodworking operations, adhesives should be clean, easy to handle, odourless and not fume, being unfilled this enables the coating weight to be substantially reduced leading to a significant increase in mileage with no sacrifice in performance. A very high tack adhesive providing excellent adhesion to difficult substrates such as primed PVC and high pressure laminates.
Applications
Woodworking
An unfilled medium viscosity adhesive for soft forming and edgebanding where difficult substrates are used, e.g. PVC, HPL, Solid Wood etc.
No filler so very little burning is encountered, optimum operating temperature 180 / 190 degrees
BAM 308 is a new concept in edgebanding hot melt adhesives based on the idea that for quality woodworking operations, adhesives should be clean, easy to handle, odourless and not fume, being unfilled this enables the coating weight to be substantially reduced leading to a significant increase in mileage with no sacrifice in performance. A very high tack adhesive providing excellent adhesion to difficult substrates such as primed PVC and high pressure laminates.
Applications
Woodworking
An unfilled medium viscosity adhesive for soft forming and edgebanding where difficult substrates are used, e.g. PVC, HPL, Solid Wood etc.
No filler so very little burning is encountered
Suggested application temperature is 180 degreesC to 200 degreesC
GLUE POT CLEANER for Edgebanding machines is a highly concentrated blend of chemicals and penetrating agents formulated to quickly breakdown all grades of hot melt adhesive from glue pots and knuckle joints.
The unique formulation of GLUE POT CLEANER together with its soak tank application saves the costly man hours of trying to scrape and burn out excess glue.
GLUE POT CLEANER starts to work immediately on contact and rapidly breaks down all deposits.
GLUE POT CLEANER is non-corrosive.
Simply immerse the glue pots in a dip tank and leave for approx 12-24 hours depending on the severity of the build-up. (Apply a thin uniform coat of GARDEX to newly cleaned pots in order to help prevent any future unwanted hot melt deposits.)
(Easy to follow instructions are on every pack)
Guide Component Kit for ST92A Stationary Worktable for AR50 Edgebanders.
Extended bolted-on accessory tool for ST95 Stationary Worktable, ST97 Guide Component Kit is ideal for higher volume production on straight-line edgebanding and trimming operation.
Constant contact with moisture and steam can cause the furniture panels to swell.
The Riepe Hydro Pen seals already finished workpiece edges against moisture penetration and extends their
water resistance many times over. Ideal for quick use in all areas - even on the road when you are on site.
The application is simple: Open the pen, draw the special felt tip over the area to be sealed and let it dry for a short time. HydroPen is the answer
.. Easy to apply
.. High yield (ca. 350 rm)
.. Fast drying
.. Nearly invisible
.. Fast and flexible to use everywhere
Rinse aid for PUR edging hot melt adhesives with high viscosity.
Due to a special additive, the chemical reaction of the PUR hotmelt adhesive is prevented during the flushing procedure. Allow all adhesive to be extruded for completely. Then fill the unit with the Jowat flushing agent and melt. The entire amount of flushing agent has to be run through the hose and nozzle; then repeat the procedure to ensure that all hot melt residues have been removed. Before taking up the work again, the flushing agent has to be completely removed from the equipment. If this is not done, it may be possible that the desired crosslinking reaction will not take place when reactive PUR hot melt adhesives are processed.
Processing temp ['C] 130-150
Apeparance: REd
Density at 23'C [G/CM3] approx 0.95 + 0.02
Softening range ['C] approx 80+5
Jowat flushing agents purge the adhesive and stop the chemical reaction of PUR hot melt adhesives. Before the cleaning of the application system is started, it must be ensured that the Jowat flushing agents and the adhesive used are compatible. To prevent plugged hoses or nozzles due to an unwanted reaction, especially in closed application systems, it must be ensured that the PUR hot melt adhesive and the Jowat? flushing agent are melted evenly.
The primary task of a flushing agent is to push out the adhesive from the hoses and the application unit, and therefore to purge product remnants from the system. Due to the general flow behaviour of liquids (cf. figure 1, on the right), the flow velocity is significantly lower at the walls compared to the centre of the hose. To ensure that the hoses are cleaned thoroughly, it is thus necessary to use a sufficient amount of flushing agent.
Apart from flow velocity, viscosity also plays a role in the purging process. If the viscosity of the flushing agent is too low, it will only purge the adhesive in the centre of the hose. Under those circumstances, it will not be possible to remove all the adhesive. To find out the viscosity of the flushing agent and the hot melt adhesive, please refer to the corresponding Technical Data Sheets (available upon request).
Jowatherm 282.40 Light yellow EVA
Edgebanding Adhesive for bondingof resinated decor paper or veneer (with fleece backing) at low processing temperatures. The properties of the bonded parts and, where necessary, the reverse primer coating of the edgebanding materials have to undergo application-related testing prior to use.
The adhesive granulate can be processed using automatic feed systems. In that case, the ambient temp should not exceed 30 Degrees.
Different types of hot melt adhesives may be incompatible with each other depending on the formulation. Therefore, we recommend to carefully clean the application equipment when changing the product. Further information is available upon request. The processing characteristics may vary depending on the application technology used as well as at differing feed speels. Preliminary testing has to be carrier out in order to assess the effect on the bonding process.
Techinical specification:
Processing temp ['C] 130-150
Feed speed [m/min] 5 - 20
Appearance light yellow
Softening range approx 85 + 5
Heat resistance ['C] approx 80 + 5
Open time at 140'C approx 10+2
HS 300 Large Adjustable Height Work Table - Beck products are characterised by technology, quality and know-how. In particular, our unique selling point, the double horizontal scissor construction, ensures maximum stability with two fixed bearings and two floating bearings. [NB this is the base unit only - tops can be added as extra to customise your solution] Max load 300 kg Useful stroke 610 mm Height of the lifting table 400 mm Weight approx. 150 kg 4 swivel castors (wheel ¢ 125 mm), 2 of which have brakesLead Time: 93 DaysList £3,507.60£2,625.00Inc Vat £3,150.00
CMT part no:DET-001 Attach this trimmer to your workpiece, press both ends against the board for a cutting range between 13mm (1/2") and 25mm (1"), move the trimmer in the correct direction indicated by the arrow. This will cut on both sides easily. The first cutter will cut straight, the second one can be adjusted for a chamfer cut. Both cutters are made from high-quality hardened steel and can be easily replaced when worn out [ Part no CMDET001K] suitable for up to 0.6mm edgingIn StockList £31.20£21.00Inc Vat £25.20
CMT part no:DET-002 Edge banding end trimmer An indispensable tool for easy and safe end trimming after edge banding. Position the tool on the banding, press down on the handle to operate the blade in a shearing action. The cutting knives are interchangeable, so when the cutting knife becomes dull, you can simply replace it with the anvil knife for a double lifetime. For cutting banding up to 0,5mm thick with a maximum cutting width of 54mm. This tool can also be paired up with our double edge trimmer DET-001. We recommend using our edge banding end trimmer DET-002 before using our double-edge trimmer DET-001.In StockList £70.80£47.00Inc Vat £56.40
CMT part no:DET-004 CMT Edgebanding Iron 230v Apply pre-glued edge banding easily and accurately. The iron non-stick surface allows smooth and easy application. The thermostatically controlled short preheat time gets you working quicker. Includes heat resistant metal base to place iron when not using it. - Includes thermostatic heat control. - Non-stick coating. - Specially shaped shoe with rounded edges. - Metal stand. - 154cm (5-1/2') power cord, 230V.In StockList £86.40£58.00Inc Vat £69.60
Made with both professionals and hobbyists in mind, the VH03 Vacuum Clamp Set is suited for edgebanding or edge tape application on large work pieces, including doors, panels, and countertops. Quick Setup Simply adhere the vacuum or C-clamp to stabilizing surface and workpiece, and flip the fasteners. Secure Your Workpieces Each vacuum cup can hold up about 34kg (75lbs) of pressure. Scuff-Free Fastening Since the vacuum cups are made of rubber, there will be no need to worry about potential damage to the workpiece or stabilizing surface. Easy Transportation Each VH03 Vacuum Clamp Set comes with two vacuum clamps and an interlockable Cruiser Case.Lead Time: 15 DaysList £240.00£175.00Inc Vat £210.00
The iTECH Panel Saw Trolley is the ultimate workshop companion, designed to simplify manual handling tasks. Ideal for single-person loading of 8x4 or 10x5 ft sheets onto horizontal saws or CNC Routers. This trolley features rubber idle rollers for effortless offloading. With adjustable height settings and a balanced design, transitioning sheets from vertical to horizontal is easy and efficient. The EASY Lift panel trolley ensures safe and affordable handling, making it a must-have for any woodworking or manufacturing workshop. Support rail distance 1150mm internal 1235mm external Packed dimensions 1500 x 480 x 110mmIn StockList £420.00£280.00Inc Vat £336.00
Spray onto the upper and lower edge area of the workpiece -Statically discharges the edge area -Cooling of the glue joint and hardening of the glue -Tracers and workpieces remain free of chippings Tooling remains free of glue residue To cool the glue joint and statically discharge the edging material. The perfect addition to the release agent spraying system fitted at the machine infeed and the cleaning agent spraying system fitted at the end of the machine is the antistatic coolant system. It can be fitted downstream of the last contact pressure roller, upstream of the cross cut saws or upstream of the radius milling stations. The Antistatic Coolant LP289/99? is sprayed directly on the glue joint and on the edging material by means of our spraying systems. As a result the glue joint surface is hardened. The glue build-up on the tools is notably reduced and consequently the glue is no longer transferred onto the edging material (indispensable for PUR). Furthermore, the edging material is statically discharged. Tracer rollers and workpieces remain free from milling chips. Milling of (flush trimming) the PVC/PP/etc. edges causes static charging of the edging material and the adjoining top and bottom face of the workpieces. Milled off chips adhere to the edging material and on the top and bottom surface of the panel negatively impairing the function of the tracer rollers and making a precise finishing by scraper blades or milling impossible. This system remedies the above problems instantly!In StockList £198.00£95.00Inc Vat £114.00
Spray onto the upper and lower edge area of the workpiece. -Statically discharges the edge area -Cooling of the glue joint and hardening of the glue -Tracers and workpieces remain free of chippings Tooling remains free of glue residue To cool the glue joint and statically discharge the edging material. The perfect addition to the release agent spraying system fitted at the machine infeed and the cleaning agent spraying system fitted at the end of the machine is the antistatic coolant system. It can be fitted downstream of the last contact pressure roller, upstream of the cross cut saws or upstream of the radius milling stations. The Antistatic Coolant LP289/99 is sprayed directly on the glue joint and on the edging material by means of our spraying systems. As a result the glue joint surface is hardened. The glue build-up on the tools is notably reduced and consequently the glue is no longer transferred onto the edging material (indispensable for PUR). Furthermore, the edging material is statically discharged. Tracer rollers and workpieces remain free from milling chips. Milling of (flush trimming) the PVC/PP/etc. edges causes static charging of the edging material and the adjoining top and bottom face of the workpieces. Milled off chips adhere to the edging material and on the top and bottom surface of the panel negatively impairing the function of the tracer rollers and making a precise finishing by scraper blades or milling impossible. This system remedies the above problems instantly!In StockList £343.20£243.00Inc Vat £291.60
Ensure the consistent high quality of your work-pieces by including the cleaning of the chain plates in your maintenance cycle. Contaminated chain plates lessen the grip on the workpiece and as a result the applied pressure of the top pressure belt has to be increased. In addition, contaminated chain plates can result in markings on the workpieces. Our specially developed Cleaning Agent LP407/13 for chain plates, top pressure belts and rubberised roller conveyors will greatly assist in cleaning without attacking any of the materials. -Specially developed for the cleaning of chain plates, top pressure belts and rubberised roller conveyors -High cleaning power -Materials not affected -Consistent grip of the workpiece -No Change in the shore hardness Unsuitable cleaners can cause damage to the sur-face of the plates. In addition, a change in the shore hardness can occur. Even a liberal use of LP407/13 has no negative ef-fect on the chain plates, top pressure belts or roller conveyors. Application: With the machine stationary, use a well wetted lint free cloth to clean plate by plate. Available containers: 10 Litre | 30 LitreIn StockList £188.40£135.00Inc Vat £162.00
Ensure the consistent high quality of your work-pieces by including the cleaning of the chain plates in your maintenance cycle. Contaminated chain plates lessen the grip on the workpiece and as a result the applied pressure of the top pressure belt has to be increased. In addition, contaminated chain plates can result in markings on the workpieces. Our specially developed Cleaning Agent LP407/13 for chain plates, top pressure belts and rubberised roller conveyors will greatly assist in cleaning without attacking any of the materials. -Specially developed for the cleaning of chain plates, top pressure belts and rubberised roller conveyors -High cleaning power -Materials not affected -Consistent grip of the workpiece -No Change in the shore hardness Unsuitable cleaners can cause damage to the sur-face of the plates. In addition, a change in the shore hardness can occur.Even a liberal use of LP407/13 has no negative ef-fect on the chain plates, top pressure belts or roller conveyors. Application: With the machine stationary, use a well wetted lint free cloth to clean plate by plate. Available containers: 10 Litre | 30 LitreLead Time: 5 DaysList £532.80£377.00Inc Vat £452.40
Spray onto the upper and lower edge area of the workpiece: - Removal of release agent and loose glue residue - Cooling of the edgeband and glue joint - Matt radius of the machined edgeband re-matches the surface finish Area of application: Before buffing wheels / surface scraper. This system is used to spray the Cleaning Agent LP163/93 on the top and bottom surface of the board edge, as well as the edgeband. The release agent applied at the machine infeed side and the loose glue residue are removed by the application of the cleaning agent and subsequent buffing. Furthermore, the glue joint and the edge banding are cooled. Heat generation during buffing is considerably reduced by the application of the liquid. Smearing of glue emerging from the joint is avoided. The edge banding radius is wet buffed with the special Cleaning Agent LP163/93. Moreover, the radius is polished to match the surface sheen. Glue residue no longer adheres to the buffing wheels. Result: An absolutely clean board edge! This result can only be obtained when the buffing wheels are used without oscillation and applying only slight pressure. The buffing disc must be used with an inclination in relation to the workpiece of 3 degrees, 10 degrees inclined to the support and with a lateral overhang of 5mm to the workpiece edge. Rotational direction should be in synchronous run to reduce heat generation. At the currently installed flat scrapers with skids the fine nozzles are arranged directly in front of the flat scraper. This prevents the adhesion of glue residue on the scrapers and skids. Consumption per fine nozzle: Under 1 liter for 5000 running meters. The electronically controlled cleaning agent spraying system only requires a compressed air connection of 3 bar and a 230/24 V socket.In Stock£327.00£392.40
The special plastic cleaners developed by RIEPE? are the first choice for the manual cleaning of plastic surfaces. Due to the exclusive use of only high quality raw materials, the RIEPE? special plastic cleaners affirm their position as premium products in the market. -Effortlessly removes glue residues -Strong cleaning power -Quick drying -Residue free evaporation -Low odour -Hexane free -Benzene freeIn StockList £108.00£66.00Inc Vat £79.20
The special plastic cleaners developed by RIEPE? are the first choice for the manual cleaning of plastic surfaces. Due to the exclusive use of only high quality raw materials, the RIEPE? special plastic cleaners affirm their position as premium products in the market. -Effortlessly removes glue residues -Strong cleaning power -Quick drying -Residue free evaporation -Low odour -Hexane free -Benzene freeLead Time: 5 DaysList £218.40£154.00Inc Vat £184.80
Spray onto the upper and lower edge area of the workpiece: Removal of release agent and loose glue residue Cooling of the edgeband and glue joint Matt radius of the machined edgeband re-matches the surface finish Area of application: Before buffing wheels / surface scraper This system is used to spray the Riepe Cleaning Agent LP163/93. On the top and bottom surface of the board edge, as well as the edgeband. The release agent applied at the machine infeed side and the loose glue residue are removed by the application of the cleaning agent and subsequent buffing. Furthermore, the glue joint and the edge banding are cooled. Heat generation during buffing is considerably reduced by the application of the liquid. Smearing of glue emerging from the joint is avoided. The edge banding radius is wet buffed with the special Cleaning Agent LP163/93. As a consequence, heating of the thermoplastic material is notably reduced, and a smearing of the plastic is prevented. Moreover, the radius is polished to match the surface sheen. Glue residue no longer adheres to the buffing wheels. Result: An absolutely clean board edge! This result can only be obtained when the buffing wheels are used without oscillation and applying only slight pressure. The buffing disc must be used with an inclination in relation to the workpiece of 3 degrees, 10 degrees inclined to the support and with a lateral overhang of 5mm to the workpiece edge. Rotational direction should be in synchronous run to reduce heat generation. At the currently installed flat scrapers with skids the fine nozzles are arranged directly in front of the flat scraper. This prevents the adhesion of glue residue on the scrapers and skids. Consumption per fine nozzle: Under 1 liter for 5000 running meters. The electronically controlled cleaning agent spraying system only requires a compressed air connection of 3 bar and a 230/24 V socket.In StockList £180.00£105.00Inc Vat £126.00
Intermittent application to the pressure roller Use within high heat zones possible Contamination of the roller is prevented The fine nozzle of this electronically controlled unit applies the Release Agent NFLY? to the contact pressure roller. This is achieved by adjustable timing interval. The spray duration is about 3 seconds. In this way glue is prevented from adhering to the contact pressure rollers. In addition the special release agent is taken from the edge and transferred to the downstream contact pressure rollers or anti-friction shoes. The contact pressure rollers and the anti-friction shoes remain free of glue residue. The anti-friction shoes are simultaneously cooled. Result: A notably enhanced quality. Contact pressure rollers and anti-friction shoes need no longer be cleaned.Lead Time: 5 DaysList £135.60£97.00Inc Vat £116.40
Intermittent application to the pressure roller Use within high heat zones possible Contamination of the roller is prevented The fine nozzle of this electronically controlled unit applies the Release Agent NFLY? to the contact pressure roller. This is achieved by adjustable timing interval. The spray duration is about 3 seconds. In this way glue is prevented from adhering to the contact pressure rollers. In addition the special release agent is taken from the edge and transferred to the downstream contact pressure rollers or anti-friction shoes. The contact pressure rollers and the anti-friction shoes remain free of glue residue. The anti-friction shoes are simultaneously cooled. Result: A notably enhanced quality. Contact pressure rollers and anti-friction shoes need no longer be cleaned.Lead Time: 5 DaysList £396.00£280.00Inc Vat £336.00
Spray onto the upper and lower edge area of the workpiece. Prevents the adhesion of emerging glue onto the workpiece. Area of application: Prior to the pre-milling Upstream of the formatting unit, an ultra-thin coat of the Release Agent is applied to the top and bottom surface of the workpieces (edge area) by means of electronically controlled release agent spraying system. This prevents squeezed out glue from adhering to the workpiece. An ultra-thin application of the release agent in the edge area (consumption per nozzle under 1 liter per 5000 running meters) guarantees a perfect result. The electronically controlled release agent spraying system only requires a 3 bar compressed air connection and a 230/24V outlet. The special release agents are adapted to all commercially available glues.In StockList £432.00£320.00Inc Vat £384.00
Spray onto the upper and lower edge area of the workpiece. Prevents the adhesion of emerging glue onto the workpiece. Area of application:Prior to the pre-milling Upstream of the formatting unit, an ultra-thin coat of the Release Agent is applied to the top and bottom surface of the workpieces (edge area) by means of electronically controlled release agent spraying system. This prevents squeezed out glue from adhering to the workpiece. An ultra-thin application of the release agent in the edge area (consumption per nozzle under 1 liter per 5000 running meters) guarantees a perfect result. The electronically controlled release agent spraying system only requires a 3 bar compressed air connection and a 230/24V outlet. The special release agents are adapted to all commercially available glues.In Stock£135.00£162.00
High heat resistant: for use on machines with high heat zones (e.g. Post-/Softforming) Workpieces can pass through high heat zones without any effect on the performance of the release agent Prevents the adhesion of emerging glue residue onto the workpieceLead Time: 5 DaysList £486.00£343.00Inc Vat £411.60
Areas of application: (a) Pressure roller (b) Edgeband/ protective foil (c) Slide shoe (d) DUO scraper (e) Tooling (a) Intermittent application to the pressure roller Glue residues cannot adhere to the roller (b) Spray directly onto the surface of the edgeband Avoidance of marking and damage Protective film is protected and not removed from the edge (c) Edge/protective foil automatically transfers the release agent to the slide shoes Glue residues do not adhere Prevents marking and friction (d) Direct application onto the DUO scraper No clogging of the DUO scraper (e) Application to the tooling Prevents fouling of the trimmers The fine nozzle of this electronically controlled unit applies the Release Agent NFLY? to the contact pressure roller. This is achieved by adjustable timing interval. The spray duration is about 3 seconds. In this way glue is prevented from adhering to the contact pressure rollers. In addition the special release agent is taken from the edge and transferred to the downstream contact pressure rollers or anti-friction shoes. The contact pressure rollers and the anti-friction shoes remain free of glue residue. The anti-friction shoes are simultaneously cooled. Result: A notably enhanced quality. Contact pressure rollers and anti-friction shoes need no longer be cleaned. Post-/Softforming: For Post-/Softforminhg work, the Release Agent NFLY? is sprayed directly on the top coat in front of the anti-friction shoes. The special release agent is transferred to the anti-friction shoes to form a glide film. This prevents squeezed out glue residue from adhering to them and the workpiece.In Stock£135.00£162.00
Areas of application: (a) Pressure roller (b) Edgeband/ protective foil (c) Slide shoe (d) DUO scraper (e) Tooling (a) Intermittent application to the pressure roller Glue residues cannot adhere to the roller (b) Spray directly onto the surface of the edgeband Avoidance of marking and damage Protective film is protected and not removed from the edge (c) Edge/protective foil automatically transfers the release agent to the slide shoes Glue residues do not adhere Prevents marking and friction (d) Direct application onto the DUO scraper No clogging of the DUO scraper (e) Application to the tooling Prevents fouling of the trimmers The fine nozzle of this electronically controlled unit applies the Release Agent NFLY? to the contact pressure roller. This is achieved by adjustable timing interval. The spray duration is about 3 seconds. In this way glue is prevented from adhering to the contact pressure rollers. In addition the special release agent is taken from the edge and transferred to the downstream contact pressure rollers or anti-friction shoes. The contact pressure rollers and the anti-friction shoes remain free of glue residue. The anti-friction shoes are simultaneously cooled. Result: A notably enhanced quality. Contact pressure rollers and anti-friction shoes need no longer be cleaned. Post-/Softforming: For Post-/Softforminhg work, the Release Agent NFLY? is sprayed directly on the top coat in front of the anti-friction shoes. The special release agent is transferred to the anti-friction shoes to form a glide film. This prevents squeezed out glue residue from adhering to them and the workpiece.Lead Time: 5 DaysList £475.20£320.00Inc Vat £384.00
BAM 308 is a new concept in edgebanding hot melt adhesives based on the idea that for quality woodworking operations, adhesives should be clean, easy to handle, odourless and not fume, being unfilled this enables the coating weight to be substantially reduced leading to a significant increase in mileage with no sacrifice in performance. A very high tack adhesive providing excellent adhesion to difficult substrates such as primed PVC and high pressure laminates. Applications Woodworking An unfilled medium viscosity adhesive for soft forming and edgebanding where difficult substrates are used, e.g. PVC, HPL, Solid Wood etc. No filler so very little burning is encounteredIn Stock£22.00£26.40
BAM 308 is a new concept in edgebanding hot melt adhesives based on the idea that for quality woodworking operations, adhesives should be clean, easy to handle, odourless and not fume, being unfilled this enables the coating weight to be substantially reduced leading to a significant increase in mileage with no sacrifice in performance. A very high tack adhesive providing excellent adhesion to difficult substrates such as primed PVC and high pressure laminates. Applications Woodworking An unfilled medium viscosity adhesive for soft forming and edgebanding where difficult substrates are used, e.g. PVC, HPL, Solid Wood etc. No filler so very little burning is encountered, optimum operating temperature 180 / 190 degreesIn Stock£220.00£264.00
BAM 308 is a new concept in edgebanding hot melt adhesives based on the idea that for quality woodworking operations, adhesives should be clean, easy to handle, odourless and not fume, being unfilled this enables the coating weight to be substantially reduced leading to a significant increase in mileage with no sacrifice in performance. A very high tack adhesive providing excellent adhesion to difficult substrates such as primed PVC and high pressure laminates. Applications Woodworking An unfilled medium viscosity adhesive for soft forming and edgebanding where difficult substrates are used, e.g. PVC, HPL, Solid Wood etc. No filler so very little burning is encountered Suggested application temperature is 180 degreesC to 200 degreesCLead Time: 8 Days£88.00£105.60
GLUE POT CLEANER for Edgebanding machines is a highly concentrated blend of chemicals and penetrating agents formulated to quickly breakdown all grades of hot melt adhesive from glue pots and knuckle joints. The unique formulation of GLUE POT CLEANER together with its soak tank application saves the costly man hours of trying to scrape and burn out excess glue. GLUE POT CLEANER starts to work immediately on contact and rapidly breaks down all deposits. GLUE POT CLEANER is non-corrosive. Simply immerse the glue pots in a dip tank and leave for approx 12-24 hours depending on the severity of the build-up. (Apply a thin uniform coat of GARDEX to newly cleaned pots in order to help prevent any future unwanted hot melt deposits.) (Easy to follow instructions are on every pack)In StockList £146.40£115.00Inc Vat £138.00
Guide Component Kit for ST92A Stationary Worktable for AR50 Edgebanders. Extended bolted-on accessory tool for ST95 Stationary Worktable, ST97 Guide Component Kit is ideal for higher volume production on straight-line edgebanding and trimming operation.Lead Time: 136 Days£195.00£234.00
Constant contact with moisture and steam can cause the furniture panels to swell. The Riepe Hydro Pen seals already finished workpiece edges against moisture penetration and extends their water resistance many times over. Ideal for quick use in all areas - even on the road when you are on site. The application is simple: Open the pen, draw the special felt tip over the area to be sealed and let it dry for a short time. HydroPen is the answer .. Easy to apply .. High yield (ca. 350 rm) .. Fast drying .. Nearly invisible .. Fast and flexible to use everywhereIn Stock
Rinse aid for PUR edging hot melt adhesives with high viscosity. Due to a special additive, the chemical reaction of the PUR hotmelt adhesive is prevented during the flushing procedure. Allow all adhesive to be extruded for completely. Then fill the unit with the Jowat flushing agent and melt. The entire amount of flushing agent has to be run through the hose and nozzle; then repeat the procedure to ensure that all hot melt residues have been removed. Before taking up the work again, the flushing agent has to be completely removed from the equipment. If this is not done, it may be possible that the desired crosslinking reaction will not take place when reactive PUR hot melt adhesives are processed. Processing temp ['C] 130-150 Apeparance: REd Density at 23'C [G/CM3] approx 0.95 + 0.02 Softening range ['C] approx 80+5In StockList £78.00£55.00Inc Vat £66.00
Jowat flushing agents purge the adhesive and stop the chemical reaction of PUR hot melt adhesives. Before the cleaning of the application system is started, it must be ensured that the Jowat flushing agents and the adhesive used are compatible. To prevent plugged hoses or nozzles due to an unwanted reaction, especially in closed application systems, it must be ensured that the PUR hot melt adhesive and the Jowat? flushing agent are melted evenly. The primary task of a flushing agent is to push out the adhesive from the hoses and the application unit, and therefore to purge product remnants from the system. Due to the general flow behaviour of liquids (cf. figure 1, on the right), the flow velocity is significantly lower at the walls compared to the centre of the hose. To ensure that the hoses are cleaned thoroughly, it is thus necessary to use a sufficient amount of flushing agent. Apart from flow velocity, viscosity also plays a role in the purging process. If the viscosity of the flushing agent is too low, it will only purge the adhesive in the centre of the hose. Under those circumstances, it will not be possible to remove all the adhesive. To find out the viscosity of the flushing agent and the hot melt adhesive, please refer to the corresponding Technical Data Sheets (available upon request).Lead Time: 90 DaysList £264.00£205.00Inc Vat £246.00
