£ Enquire
Centauro CVS50 Door Lock & Hinge Mortiser
SKU
CECVS50
the Centauro CVS50 Door Lock Mortiser is ideal if you manufacture door sets. A great solution, allowing you to machine the complete lock fitting or use it as a standard chain mortiser. Optional pneumatic movement of the rear drill sets.
The Centauro CVS 50 is a vertical mortiser that will machine out the slot for the lock and recess for the face plate in one operation on the door blank. Then via the rear horizontal drill units (one oscillating) it is possible to produce the hole for the handle and the slot for the key. The machine is simple to use and typically the above operations can be completed in as under 2 minutes. The machine is also equipped with a standard table and pneumatic workpiece clamp for conventional chain mortising.
Features:
- Electro-weld steel frame to ensure maximum strength and stability.
- Head, carriage and working table in cast-iron.
- Working head runs on prismatic guides in hardened and ground steel with needles sliding block.
- Vertical spindles unit to carry out the lock face-plate recess at the same time as the lock slot.
- Horizontal spindles unit for drilling key and handle holes.
- System for raising the working head by gas spring.
- Mechanical front workpiece clamping.
- Pneumatic locking device for doors.
- Sawdust hood ? 60 mm.
STANDARD EQUIPMENT
- Automatic chain lubrication pump.
- Mechanical front workpiece clamping.
- Pneumatic door clamping.
- Aluminium table extension with frame Stopps.
- Emergency stop button.
- Reference/length rod for horizontal positioning of the door.
- Compressed-air gun for cleaning the machine.
- Service spanners.
OPTIONAL
- Oil-pneumatic feed of horizontal spindles.
- Pneumatic front hold-down cylinder with low pressure positioning and safety valve of working cycle start.
- Single or double chains, vertical and horizontal bits.
- Machine version according to CE standards: thermal over load cut-out for each motor, micro-switch on chain guard, padlockable
main switch, rear head guard, emergency stop button with release coil.
The Centauro CVS 50 is a vertical mortiser that will machine out the slot for the lock and recess for the face plate in one operation on the door blank. Then via the rear horizontal drill units (one oscillating) it is possible to produce the hole for the handle and the slot for the key. The machine is simple to use and typically the above operations can be completed in as under 2 minutes. The machine is also equipped with a standard table and pneumatic workpiece clamp for conventional chain mortising.
Features:
- Electro-weld steel frame to ensure maximum strength and stability.
- Head, carriage and working table in cast-iron.
- Working head runs on prismatic guides in hardened and ground steel with needles sliding block.
- Vertical spindles unit to carry out the lock face-plate recess at the same time as the lock slot.
- Horizontal spindles unit for drilling key and handle holes.
- System for raising the working head by gas spring.
- Mechanical front workpiece clamping.
- Pneumatic locking device for doors.
- Sawdust hood ? 60 mm.
STANDARD EQUIPMENT
- Automatic chain lubrication pump.
- Mechanical front workpiece clamping.
- Pneumatic door clamping.
- Aluminium table extension with frame Stopps.
- Emergency stop button.
- Reference/length rod for horizontal positioning of the door.
- Compressed-air gun for cleaning the machine.
- Service spanners.
OPTIONAL
- Oil-pneumatic feed of horizontal spindles.
- Pneumatic front hold-down cylinder with low pressure positioning and safety valve of working cycle start.
- Single or double chains, vertical and horizontal bits.
- Machine version according to CE standards: thermal over load cut-out for each motor, micro-switch on chain guard, padlockable
main switch, rear head guard, emergency stop button with release coil.
Lead Time: 73 Days
- Motor power 3hp
- Motor 4
- Maximum slot depth 150mm
- Longitudinal stroke 300mm
- Maximum slot length 340mm
- Transverse stroke 80mm
- Max height of workpiece on table 180mm
- Head rotation + / - 45 degree
- Tilt of worktable + / - 45 degree
- Maximum frame height 1000 / 700mm
- Weight 510kg
- Overall dimensions 1916 x 1400 x 1026mm
| SKU | CECVS50 |
|---|---|
| Manufacturer | Centauro |
| Phase | 3 |
Write Your Own Review
