DMC SD 60 RCS 1100 Wide Belt Sander

Base and working table
* steel structure with electric cabinet on the machine front
* sanding belts introduction from the machine left side
* powered adjustment of working thickness
* main motor positioned inside the base
Electrical equipment
* electromechanical keyboard positioned on the machine front side
* automatic star-delta start of the main motor
* overload protections on the motors
* motors in isolation class IP54
Emergency and safety devices
* automatic brake for rapid shutdown of the operating group
* hand-safety emergency device in the infeed panel area
* front and rear emergency pushbutton
* padlockable main switch
* safety micro for overthickness
* automatic emergency stop machine for:
- sanding belt breaking
- not-tensioned sanding belt
- lateral outplacement of sanding belt
- absence of compressed air
- overload on main motor
N.B. The machine with standard configuration is supplied with 400 Volt 50 Hz
and 3-phase version + neutral + earth.
When the 400 voltage supply has not the neutral phase, it is necessary to select
the single-phase transformer, foreseen on the price list.
The same transformer has to be selected also when the machine is supplied with
voltages higher than 400 volt, independently from the neutral phase presence.
The machine supply with 220 or 230 voltages (50 or 60 Hz) is foreseen in the
price list with an additional cost.

"B" versions:
"MESAR" elastic sectional pads with single adjustable pressure
C or C-Plus versions:
"MESAR" electronic sectional pads complete with:
- on/off pneumatic cylinder for pad unit
- "Logic 50" electronic programmer which synchronizes the anti-dubbing device
with the feed speed and activates the quantity according to the geometric shape
of the workpiece. It allows the selection of a higher or lower number of sections
tothe left, to the right or on both sides of the piece.
- working pressure adjustment

"MESAR 20" with 20 sectors and 55 mm distance between sectors, complete
with B/20 infeed reading bar
- "MESAR 37" with 37 sectors and 30 mm distance between sectors, complete
with B/ 37 infeed reading bar


R1.07.09 dmc sd 60 composition RCS 110
with 1st R group (roller) and 2nd CS combined group (roller/pad)

European safety regulations (CE norms)

"RA" Helicoidal grooved steel calibrat. roller-1st group

CR65 65SH rubber-coated calibr./sand.roller 2nd group

44.44.19 "B" version for RCS
complete with: on/off pneumatic selector of the roller on the 1st "R" group on/off pneumatic selector of the roller on the 2nd CS group "MESAR" elastic sectional pad on/off pneumatic selector of the pad Logic 50 K electronic programmer electronic positioning for working table

97.50.72 Main motor 18 kW (25 hp)

working width mm 1.100 1.350
min/max. working thickness mm 4-170 4-170
sanding belt width mm 1.115 1.370
sanding belt length mm 2.150 2.150
main motor power kW(HP)11(15)11 (15)
Feed belt motor power Kk (HP) 0,45/0,8
Feed speed m/min 4,5/9 4,5/9
DMC logo
  • approximate lead time: 54 days
  • Part Number: SCDMSD60RCS110
£ Enquire
Lease from only
£107.59 per week

Leasing plans are for
UK businesses only
and subject to status

Product Description
  • N/A
Additional Information
Additional Information
Part Number SCDMSD60RCS110
Manufacturer DMC

Write Your Own Review

You're reviewing: DMC SD 60 RCS 1100 Wide Belt Sander

How do you rate this product? *

  1 star 2 stars 3 stars 4 stars 5 stars
Your Rating
You may also be interested in the following product(s)