Wadkin
(92 Products)
Wadkin was one of the leading manufacturers of high quality, robust woodworking equipment in the world. Today, Wadkin no longer manufacture machines but we offer a comprehensive support, spares and back up for Wadkin machines.
-
This rubberised cork material can be used for re covering bandsaw wheels and replacing old tyres. Extremely flexible and wear resistant. Now its easy to rejuvinate you bandsaw wheels. Available in a variety of widths - sold Per Meter Thickness - 5 mm NB - Requires PA3213 AdhesiveLead Time: 136 Days£18.00£21.60 -
This rubberised cork material can be used for re covering bandsaw wheels and replacing old tyres. Extremely flexible and wear resistant. Now its easy to rejuvinate you bandsaw wheels. Available in a variety of widths - sold Per Meter Thickness - 5 mm NB - Requires PA3213 AdhesiveIn Stock£18.00£21.60
-
This rubberised cork material can be used for re covering bandsaw wheels and replacing old tyres. Extremely flexible and wear resistant. Now its easy to rejuvinate you bandsaw wheels. Available in a variety of widths - sold Per Meter Thickness - 5 mm NB - Requires PA3213 AdhesiveIn Stock£21.00£25.20
-
20ml bottle for lubrication of APA side and back roller guidesLead Time: 136 Days£21.00£25.20 -
This rubberised cork material can be used for re covering bandsaw wheels and replacing old tyres. Extremely flexible and wear resistant. Now its easy to rejuvinate you bandsaw wheels. Available in a variety of widths - sold Per Meter Thickness - 5 mm NB - Requires PA3213 AdhesiveIn Stock£27.00£32.40
-
Replacement slats for the Wadkin PAR machine. These are sold individually.Lead Time: 3 Days£27.00£32.40 -
-
3/8" Bore AUGER Bush to hold the drill auger in Wadkin DM and DM/V MorticersIn Stock£30.00£36.00 -
-
-
-
-
Nx40 4.7mm Rad & Square Stylus For Wadkin Profile Stylus for Wadin Profile Grinder different shapes suitable for Wadkin Profile Grinders NX, NV etcLead Time: 3 Days£42.00£50.40 -
-
Nx111ÿÿ 4.7mm 30 Deg Right Stylus For Wadkin Profile grinderLead Time: 3 Days£42.00£50.40 -
Nx112ÿÿ 4.7mm 30 Deg Left Stylus For Wadkin ProfiLead Time: 3 Days£42.00£50.40 -
-
NX133 3mm Radius and square stylus for Wadkin NX grinderLead Time: 3 Days£42.00£50.40 -
A high quality rear thrust bearing, mounted on sleeve for bandsaw guides. 35mm dia bearing mounted on a sleeve 40 x 20mm This size fits the GL456 bandsaw guide (top or bottom) as mounted to many makes of industrial bandsaw up to 600mm wheel such as Wadkin, Centauro, SCM 35mm dia bearing mounted on a sleeve 40 x 20mmIn Stock£49.00£58.80 -
Set of 50ml permabond adhesive complete with initiator for fixing bandsaw tyres (recommended one set per wheel) Instructions: The rim of the Bandsaw Wheel being treated should be cleaned thoroughly removing all traces of old rubber and adhesive right down to the bright metal surface. Do not use oil based cleaning materials, such as paraffin as this will be detrimental to the use of the new adhesive applied. For the strongest adhesive to metal, Primer should be used. This must be stirred thoroughly prior to the application of a medium brush coat to prepared metal surfaces. Allow the primer to dry for at least one hour before applying the adhesive. Prepare the rubber tyre by wiping thoroughly with a clean rag and lightly roughen the inside with emery paper. Apply an even film of the mixed adhesive to both surfaces by brush, roller or serrated trowel. Allow these to dry for 10-20 minutes or until they can be touched by the knuckles Without any adhesive being transferred. Joining the Surfaces. As the tyre has to be stretched onto the rim of the wheel, care must be taken to ensure that the tyre lies central on the wheel rim. As the adhesive is a contact' type, it is advisable to place spacers between the tyre and the wheel at 3"- 4" intervals until the centralisation mentioned above has been achieved. The spacers can then be removed allowing the adhesive surfaces to come together. As much pressure as possible should be applied to the tyre to ensure a good bonding - paying special attention to the edges. The wheels should be allowed to stand for 1-2 hours before use. Finally, true up the rubber and put a slight crown on the face. This is done by revolving the wheel, preferably on the machine, and holding against it a wooden block covered with emery cloth. Check the wheel for balance before use. An alternative method to the above is to apply the adhesive to one surface only and bond immediately. This will give a much lower initial bond strength than the previous method. Maximum bond strength using this method will take approximately 5-7 days to develop. F'. U 1Lead Time: 3 Days£49.00£58.80 -
Upper Back Roller Complete On Shaft Panhans APA2 Guides 58mm bearing on 22mm shaftLead Time: 136 Days£64.00£76.80 -
-
-
-
-
-
-
-
-
-
Clutch Plate / disc for rise and fall on thicknesser bed on Wadkin BT500 Thicknesser Wadkin BTS500 Planer Thicknesser Wadkin BT630 Thicknesser Wadkin BTS630 Planer ThicknesserLead Time: 3 Days£79.00£94.80
-
A high quality rear thrust bearing, mounted on sleeve for bandsaw guides. 50mm diameter roller mounted on a 20mm diameter shaft This size fits the GL789 saw guide (top or bottom) as mounted to many makes of industrial bandsaw up to 900mm wheel such as Wadkin, Centauro, SCM 50mm diameter roller mounted on a 20mm diameter shaftIn Stock£80.00£96.00 -
Grinding wheel for Wadkin NQ straight knife grinder. Suitable for HSS planer bladesLead Time: 3 Days£85.00£102.00 -
-
13/16" Chisel bush for smaller chisels on Wadkin EDA Tradesman mortiserLead Time: 3 Days£92.00£110.40
