Sold & Discontinued Machines
(368 Products)
-
Trend 47/6AX1/4TC D=24 mm C=12.0 A=60 degrees Shank Diameter=1/4 inch . Three bevel cutters for edging . For trimming laminate, when a wider edge line is preferred on the finished edge. Supplied in 80 degree, 60 degree and 30 degree versions of bevel angle. No bottom cut.Lead Time: 9 Days£ Enquire£ Enquire
-
-
-
Trend 50/32X8MMHSSE D=5 mm C=40 mm OL=100 mm Shank Diameter=8.0 Rec. speed=10000-12000 rpm . For drilling and slotting uPVC plastic. Cutters are designed to plunge and machine or mill lateral slots. Material should be securely clamped. Two flute helical up-cut. The long shanks are ideal for water slot routing.Lead Time: 9 Days£ Enquire£ Enquire
-
Trend 50/35X8MMHSSE D=5 mm C=35 mm OL=80 mm Shank Diameter=8.0 Rec. speed=10000-12000 rpm . For drilling and slotting uPVC plastic. Cutters are designed to plunge and machine or mill lateral slots. Material should be securely clamped. Single flute straight. The long shanks are ideal for water slot routing.Lead Time: 9 Days£ Enquire£ Enquire
-
Trend 620/9WS D=20 mm D2=9 mm OL=25 mm . These countersinks, produced from the best grade carbon steel, leaves a clean cut finish by virtue of their multi-tooth deep ground gullets. Fits metric drills from 3mm to 12mm inclusive. Not suitable for abrasive materials or metal.Lead Time: 9 Days£ Enquire£ Enquire
-
Trend 6200/12HSS D=15.9 mm D2=6.35 mm Shank Dia.=Drill Chuck . They are designed to drill and coutersink simultaneously, a wide variety of materials. Supplied with a HSS slow spiral drill bit. Fully adjustable, a hex key is supplied. Use at drilling speeds only. Not suitable for ferrous orLead Time: 9 Days£ Enquire£ Enquire
-
Trend 7/60X1/2TC D=36.0 D2=16.0 C=35 mm R=10.0 Shank Diameter=1/2 inch . Simultaneously rounds over and profiles the edge. Ideal for pencil round architrave.Lead Time: 9 Days£ Enquire£ Enquire
-
Trend 7/61X1/2TC D=30 mm D2=16.0 C=30 mm R=5 mm A=85 degrees Shank Diameter=1/2 inch . Simultaneously rounds over and profiles the edge. Ideal for a modern skirting board mould.Lead Time: 9 Days£ Enquire£ Enquire
-
Trend 7/7X1/4TC D=41 mm C=20 mm R=15 mm Shank Diameter=1/4 inch . Some Ovolo cutters can be used with radius cutters, to make rule joints. Ref. 7/01 has an extra long shank of 40mm.Lead Time: 9 Days£ Enquire£ Enquire
-
Trend 7/96X12MMTC D=54 mm C=25 mm B=21.8.0 A=75 degrees R=12.7 mm Shank Diameter=12.0 . Especially designed for routing Corian, and similar luxury inchmarble like' material which is used in many bathrooms and kitchens. For finishing undermount bowl. Without lip.Lead Time: 9 Days£ Enquire£ Enquire
-
Trend 7/98X1/2TC D=57 mm C=19 mm C2=25.4 mm B=21.8.0 A=72 degrees R=12.7 mm Shank Diameter=1/2 inch . Especially designed for routing Corian, and similar luxury inchmarble like' material which is used in many bathrooms and kitchens. For finishing undermount bowl. With lip.Lead Time: 9 Days£ Enquire£ Enquire
-
Trend 7/98X12MMTC D=57 mm C=19 mm, C2=25.4 mm B=21.8.0 A=72 degrees R=12.7 mm Shank Diameter=12.0 . Especially designed for routing Corian, and similar luxury inchmarble like' material which is used in many bathrooms and kitchens. For finishing undermount bowl. With lip.Lead Time: 9 Days£ Enquire£ Enquire
-
Trend 7/99X1/2TC D=60.7 mm C=25 mm C2=32 mm B=21.8.0 A=72 degrees R=14 mm Shank Diameter=1/2 inch . Especially designed for routing Corian, and similar luxury inchmarble like' material which is used in many bathrooms and kitchens. For finishing undermount bowl. With lip.Lead Time: 9 Days£ Enquire£ Enquire
-
Trend 7/99X12MMTC D=60.7 mm C=25 mm C2=32 mm B=21.8.0 A=72 degrees R=14 mm Shank Diameter=12.0 . Especially designed for routing Corian, and similar luxury inchmarble like' material which is used in many bathrooms and kitchens. For finishing undermount bowl. With lip.Lead Time: 9 Days£ Enquire£ Enquire
-
Trend 755X12MMTC D=38.0 B=28.0 OL=96.0 Shank Diameter=12.0 Timber thickness min.=10.0 (without bearing fitted) Timber thickness max.=32 mm . Two rounded corners can be cut simultaneously. By adjusting the assembly of spacers on the arbor, timber between 10.0 and 32mm thick can be moulded. Central guide bearing can be removed and fitted above or below the cutters.Lead Time: 9 Days£ Enquire£ Enquire
-
Trend 768X1/2TC D=35 mm B=22 mm R=6.3 mm R2=4.8.0 OL=108.0 Shank Diameter=1/2 inch Mode AB Timber thickness min.=12.7 mm Mode AB Timber thickness max.=38.0 Mode BA Timber thickness min.=9.6.0 Mode BA Timber thickness max.= . Allows two rounded corners to be cut simultaneously. By swapping positions of the blocks the radii can be changed. Smaller timber thicknesses can be accommodated by mounting the bearing below both blocks and following a template.Lead Time: 9 Days£ Enquire£ Enquire
-
Trend 8/43X1/2TC D=22.0 mm C=1 inch C=25.4 mm B=12.7 mm R=19.5 mm Shank Diameter=1/2 inch . The bearing guided cutters are quick to set up & can be used for curved screens, doors etc. No side fence required.Lead Time: 9 Days£ Enquire£ Enquire
-
Trend 8/44X1/2TC D=25.4 mm C=38.1 mm B=12.7 mm R=32 mm Shank Diameter=1/2 inch . The bearing guided cutters are quick to set up & can be used for curved screens, doors etc. No side fence required.Lead Time: 9 Days£ Enquire£ Enquire
-
Trend 87/01X1/2TC D=47.5 mm D2=37 mm C=30 mm Shank Diameter=1/2 inch Timber thickness min.=14 mm Timber thickness max.=25 mm . A heavy duty reversible finger jointer, to increase the gluing area for edge to edge joints.Lead Time: 9 Days£ Enquire£ Enquire
-
Trend 9/04X1/4TC D=19.1 mm C=25 mm R=2 mm R2=6.0 Shank Diameter=1/4 inch . Decorative edge moulds for shelf edges.Lead Time: 9 Days£ Enquire£ Enquire
-
Trend 9/41X1/4TC D=23.8.0 C=17 mm B=9.5 mm R=7.14 mm A=45 degrees Shank Diameter=1/4 inch Timber thickness min.=14 mm Timber thickness max.=15 mm . Cutters to create a knuckle joints for gate leg tables. The cutter should be used in a router table. Hand tools will be required to finish the joint.Lead Time: 9 Days£ Enquire£ Enquire
-
Trend 9/77X1/2TC Diameter=25 mm C=25 mm B=19 mm R=3 mm R2=5 mm OL=78.0 Shank Diameter=1/2 inch . Decorative edge moulds for shelf edges.Lead Time: 9 Days£ Enquire£ Enquire
-
Trend 9/87X1/2TC D=1 inch D=25.4 mm C=22 mm B=16.0 R=10.5 mm R2=5 mm Shank Diameter=1/2 inch . Decorative edge mould for shelves. Edge moulding applications only.Lead Time: 9 Days£ Enquire£ Enquire
-
Trend 9/88X1/2TC D=1 inch D=25.4 mm C=22 mm B=16.0 R=25.5 mm R2=2.5 mm Shank Diameter=1/2 inch . Decorative edge mould for shelves. Edge moulding applications only.Lead Time: 9 Days£ Enquire£ Enquire
-
Trend 90/10X1/2TC D=25 mm C=22 mm C2=16.0 B=19 mm R=6.0 Shank Diameter=1/2 inch Material thickness=13 mm . Creates the waterfall edge on worktops.Lead Time: 9 Days£ Enquire£ Enquire
-
Trend 90/10X12MMTC D=25 mm C=22 mm C2=16.0 B=19 mm R=6.0 Shank Diameter=12.0 Material thicknes=13 mm . Creates the waterfall edge on worktops.Lead Time: 9 Days£ Enquire£ Enquire
-
Trend 90/20X1/2TC D=54 mm C=20 mm B=28.57 mm R=12.7 mm Shank Diameter=1/2 inch . Especially designed for routing Corian, and similar luxury inchmarble like' material which is used in many bathrooms and kitchens. For bullnose moulding use Ref. 90/20 inconjunction with Ref. 90/25 and Ref. 90/21 with Ref. 90/28.Lead Time: 9 Days£ Enquire£ Enquire
-
Trend 90/20X12MMTC D=54 mm C=20 mm B=28.57 mm R=12.7 mm Shank Diameter=12.0 . Especially designed for routing Corian, and similar luxury inchmarble like' material which is used in many bathrooms and kitchens. For bullnose moulding use Ref. 90/20 inconjunction with Ref. 90/25 and Ref. 90/21 with Ref. 90/28.Lead Time: 9 Days£ Enquire£ Enquire
-
Trend 90/21X12MMTC D=67 mm C=25 mm B=28.57 mm R=19 mm Shank Diameter=12.0 . Especially designed for routing Corian, and similar luxury inchmarble like' material which is used in many bathrooms and kitchens. For bullnose moulding use Ref. 90/20 inconjunction with Ref. 90/25 and Ref. 90/21 with Ref. 90/28.Lead Time: 9 Days£ Enquire£ Enquire
-
Trend 90/32X12MMTC D=1 inch D=25.4 mm C=12.0 R=16.0 R2=11 mm Shank Diameter=12.0 . The Roman Ogee Ref. 90/32 is used to form a waterfall edge with Ref. 90/26. Ref. 90/34 is used to create a shadow line with flush mount sinks.Lead Time: 9 Days£ Enquire£ Enquire
-
Trend 92/1X1/2TC D=1 inch D=25.4 mm C=45 mm B=12.7 mm R=3.5 mm R2=19 mm R3=7 mm Shank Diameter=1/2 inch . The whole profile edge of the cutter can be used for skirting boards and period style finishes in furniture. Different parts of these cutters can be used to give various profiles.Lead Time: 9 Days£ Enquire£ Enquire
-
Trend 92/24X1/2TC D=30 mm D2=26.0 C=35 mm B=16.0 R=12.0 R2=6.0 Shank Diameter=1/2 inch . A bullnose mould with additional decorative embellishments.Lead Time: 9 Days£ Enquire£ Enquire
-
Trend 92/26X1/2TC D=45 mm D2=23 mm C=30 mm B=16.0 R=38.0 R2=2.5 mm Shank Diameter=1/2 inch . Classic cutter for bolection mould, used on panelled doors or heavy cornice work. Also for architraves, framing as well as edge moulding.Lead Time: 9 Days£ Enquire£ Enquire
-
Trend 92/27X1/2TC D=40 mm D2=26.0 C=30 mm B=16.0 R=5.5 mm R2=5 mm Shank Diameter=1/2 inch . Classic cutter for bolection mould, used on panelled doors or heavy cornice work. Also for architraves, framing as well as edge moulding.Lead Time: 9 Days£ Enquire£ Enquire
-
Trend 92/28X1/2TC D=75 mm C=6.0 Shank Diameter=1/2 inch . Especially designed for routing Corian, which is used in many bathrooms and kitchens. Specialist tool to remove sink from the worktop.Lead Time: 9 Days£ Enquire£ Enquire
-
Trend 93/10X1/2TC D=45 mm C=1 inch C=25.4 mm B=12.7 mm R=6.0 R2=2 mm Shank Diameter=1/2 inch . Ideal for edging traditional picture frames, mirrors, clocks and plaques.Lead Time: 9 Days£ Enquire£ Enquire
-
Trend ACR2/80X1/2TC D=1/2 inch D=12.7 mm C=1 1/4 inch C=32 mm Shank Diameter=1/2 inch Overall length=76.0 . Single flute for fast cutting. Specially ground for cutting acrylic. Cutter ref ACR2/80 can be used on phenolic resin.Lead Time: 9 Days£ Enquire£ Enquire
-
Trend ACRS2/6X1/4STC D=1/4 inch D=6.3 mm C=10.0 Shank Diameter=1/4 inch Overall length=51 mm . Single flute for fast cutting. Specially ground for cutting acrylic. Cutter ref ACR2/80 can be used on phenolic resin.Lead Time: 9 Days£ Enquire£ Enquire
-
Trend AQ21/B/25 Colour=Brown Length=25m Seal size excl barb=11.5mmx9.8mm . Strip is fitted into the door frame rebate (head and jambs) as three cut pieces forming a compression or wiping seal. The seal is butt joined at the corners. To seal the door bottom, a weather bar is mounted into the threshold seLead Time: 9 Days£ Enquire£ Enquire
-
Trend AQ63/B/25 Colour=Brown Length=25m Seal size excl barb=6.9mmx6.5mm . Weather strip is fitted into the window frame aperture using four cut lengths. It is important to create tight butt or notched joints to ensure high levels of window performance. Joints can be enhanced by the application of a smalLead Time: 9 Days£ Enquire£ Enquire
-
Trend CE/CNS/1 Bore=1 mm . Multi-slit spring steel collet & nut set for the 1/2 inch or 12mm shank collet extension.Lead Time: 9 Days£ Enquire£ Enquire
-
Trend CE/CNS/12 Bore=12.0 . Multi-slit spring steel collet & nut set for the 1/2 inch or 12mm shank collet extension.Lead Time: 9 Days£ Enquire£ Enquire
-
Trend CE/CNS/2 Bore=2 mm . Multi-slit spring steel collet & nut set for the 1/2 inch or 12mm shank collet extension.Lead Time: 9 Days£ Enquire£ Enquire
-
Trend CE/CNS/8/6 Bore=6.0 . Multi-slit spring steel collet & nut set for the 8mm shank collet extension.Lead Time: 9 Days£ Enquire£ Enquire
-
-
Trend CLT/T10/10 d=10.0 . A precision multi-slit one piece collet. Does not include the collet nut. For Trend T10 and T11 routers.Lead Time: 9 Days£ Enquire£ Enquire
-
Trend CLT/T10/6 Bore=6.0 . A precision multi-slit one piece collet. Does not include the collet nut. For Trend T10 and T11 routers.Lead Time: 9 Days£ Enquire£ Enquire